Muff Clip | Magnetic Tradie Belt Clip + Bit Holder

Finally — Somewhere to Put Your Muffs

If you wear hearing protection on site, you know the dance. Off the head, around the neck, hooked over your chisel, dumped in the dust on top of the toolbox — and half the time you end up sitting on them at smoko or losing them off the scaffold.

The Muff Clip sorts that out for good. It's a purpose-built clip that holds your muffs exactly where you want them — on your belt, your nailbag, your bib-and-brace strap, or just straight onto your pants. Whenever you need to talk to the foreman, take a call, or stop for a feed, you clip your muffs on and crack on. No more lost muffs. No more grit in the cushions. No more "where the hell did I put them?"

And because we couldn't help ourselves, we built in two extras people kept asking for: a monster Neodymium N52 magnet on the front, and a three-bit holder for the drivers you actually use.

Designed and Made Right Here in New Zealand

Designed, prototyped and made in New Zealand by people who actually swing the hammer. We tested it on real sites with real tradies before a single one went out the door. Every Muff Clip is built to handle Kiwi conditions — heat, dust, rain, concrete dust, the lot.

Built Strong. Built to Last.

This isn't a flimsy plastic clip that'll snap the first time you drop your nailbag off the back of the ute. The body is moulded from impact-resistant engineered polymer and reinforced where it counts — the belt jaw, the pivot, and the magnet housing. It clamps on tight, holds firm, and keeps holding shift after shift.

• Strong & Robust — Engineered polymer body built to take knocks, drops and full days of abuse without giving up.
• Universal Fit — Clips to any tool belt, nailbag, bib strap, side pocket, or even straight onto your work pants.
• Holds Your Muffs Secure — Keeps your hearing protection on you and off the ground.
• Neodymium N52 Super Magnet — One of the strongest commercially available rare-earth magnets, recessed into the front face.
• Three-Bit Holder — Hangs onto the three driver bits you reach for most, right where you can grab them one-handed.
• Designed & Made in NZ — Built by Kiwi tradies for Kiwi tradies. Tested on real worksites, not in a meeting room.

That N52 Magnet — More Useful Than You'd Think

We bolted a Neodymium grade N52 magnet to the front because once you've got one on your hip, you'll find a hundred uses for it. N52 is the top end of commercially available neodymium — seriously strong for its size. Some of the ways people on site are using their Muff Clip:

• Holds your screws, nails and fixings while you line up the next one — no more pinching three screws between your teeth.
• Picks up dropped screws and washers off the deck, out of grass, out of the gib dust — wave the Muff Clip over and they jump onto it.
• Locates fixings behind the wall — drag it across the gib and feel for the pull of nail or screw heads in the studs.
• Grabs the tape measure end so it sits put while you mark up.
• Holds your utility knife, multi-tool, small spanners or any other steel hand tool you don't want to lose down the wall cavity.
• Sticks to steel framing, scaffold tube, roller doors, the side of the ute or the back of the trailer — turning anything steel into a temporary tool bench.
• Holds extra drill bits, hex bits and driver shanks when you've got more than three on the go.
• Picks up dropped pins, hinges and brackets out of the dirt without bending down.

It's the kind of thing you don't know you need until you've got one — then you wonder how you managed without it.

Three-Bit Holder Right Where You Need It

Quick-load slots for three of your favourite driver bits — Phillips, square, Torx, whatever you run. They sit in tight, don't rattle out, and you can pull one out one-handed without taking your eyes off the work. Comes with three Mufftech impact-rated bits to get you started.

One Clip. A Hundred Uses.

• Clip your muffs on when you're not wearing them
• Throw it on any belt, nailbag, strap or waistband
• Hold the bits you actually use, right on your hip
  
• Find buried fixings without a separate tool
• Stick it to anything steel and use it as a temporary holder

Why Tradies Are Grabbing a Muff Clip

• Designed and built in New Zealand
• Solves a real, daily on-the-job problem
• Doubles as a magnetic tool and a bit holder
• Tough enough to live on your belt every day
• Works with any tool belt, nailbag or work pants
• Three impact-rated driver bits included

Stop dumping your muffs in the dust. Grab a Muff Clip and keep your hearing protection — and your favourite bits — right where they should be: on your hip and ready to go.